Error F02 in the Indesit washing machine

F02 error in IndesitThe appearance of error codes on an Indesit washing machine indicates a unit inside the equipment in which a malfunction has occurred. It is impossible to say with 100% certainty what exactly could have broken by looking at the error. Even experienced professionals cannot do this, and what can we say about a simple user who doesn’t even know how to decipher the code. Let's deal with error f02 in Indesit Strakki and find out how to fix it.

Description of the error

In short, error f02 means that the circuit in the tachometer is broken, as a result of which the electric motor does not work. It manifests itself something like this: you put the laundry in the drum, turn on the washing machine, it fills with water, tries to spin the drum several times, but nothing comes of it, it stands still. After 2-3 such attempts, this code is displayed on the display.

Code f02 is not the only one that reports a similar problem. If we talk about older units, there is no display at all on which the error would be displayed. In such machines, the problem is indicated by indicators on the control panel or a rotating programmer.

If you notice that the “quick wash” light is on or the extra rinse light is blinking, then keep in mind that this is error f02.

Reasons for appearance

The appearance of this error can be caused by various reasons, we list them:

  • malfunction of the tachometer responsible for engine speed;
  • jamming of the washing machine motor rotor;
  • faulty contacts of connector J9 on the board;
  • failure of the engine, which happens quite rarely, and even in such a situation it appears more often error F01;
  • control module failure.

Trouble-shooting

To eliminate the cause that gave rise to error F02 on the Indesit washing machine, you will have to carry out a step-by-step search for this cause. But first, try to reboot the “brain” of the machine by disconnecting it from the network for 20 minutes.

If a malfunction is confirmed, begin your search in the following order:

  1. Disconnect the machine from the water supply and sewerage system and turn it around. The washing machine should be positioned so that it is convenient for you to disassemble it;
  2. open the rear service hatch of the machine or the housing cover to see the drive mechanism;
  3. remove the drive belt from the drum pulley with one hand, while simultaneously turning the pulley itself with the other hand;
  4. unscrew the bolts holding the engine;
    engine in Indesit
  5. disconnect all wires from the engine;
  6. carefully pull it off the fastenings and pull it out of the car;
  7. now remove the speed sensor from the engine and check its serviceability using a multimeter in resistance mode, it should normally be 115-170 Ohms;
    tachometer on the engine

    To check the tachometer it is not at all necessary to remove the engine from the washing machine.

  8. Next, check the rotation of the engine rotor to see if anything is jammed;
  9. if everything is in order, proceed to check the terminals and electrical wires running from the engine to the control board.

Having finished with the motor, you need to find a module from the washing machine. It is located in the back of the washer on the right side relative to the tank, but this is not typical for all models.

control module

Disconnect all the chips from the board and take it out, we recommend taking a photo of the location of the wires. Next, check the reliability of the contacts on connector J9 of the control board; if not, replace them with new ones. Measure the resistance between the first and second contacts.

connector J9 on the Indesit board

If you find one, it is better to trust the solution to a problem with the control module to a specialist.But if it’s a matter of principle, repair the board yourself and gain experience. Perhaps you will find a like-minded person on the forum who will tell you what to solder in a specific model of washing machine, don’t despair. If there is no chance, change the module completely, just buy one already programmed, otherwise there will be problems with the firmware.

In general, error F02 on an Indesit washing machine can be solved, but not in all cases. Whether to give your washing machine to a mechanic or not, decide for yourself.

   

Reader comments

  • Share your opinion - leave a comment

Add a comment

We recommend reading

Washing machine error codes