Zanussi washing machine won't turn on

Zanussi SM does not turn onBreakdowns always occur suddenly, and often the desire to start a major laundry unexpectedly ends in nerves and bewilderment. And just recently, a properly working machine stops responding to your requests. The Zanussi washing machine does not turn on for many reasons, ranging from problems with the power supply in the room to a non-functioning hatch lock and a faulty module.

But you shouldn’t write off the washing machine and plan to buy new equipment. It is quite possible to solve the problem and continue the planned wash, just follow the instructions below.

How does the breakdown manifest itself and why does it occur?

Call it the “law of meanness,” an accident or a pattern, but sooner or later the washing machine can break down. And Zanussi automatic machines are no exception. You can notice the “SOS” signal from the washing machine by the following “symptoms”.

  1. The system does not respond to pressing the Start button. The lights do not light up, water does not fill, which does not change even after reconnecting.
  2. Power is being knocked out. After pressing the start button, several indicators light up and immediately go out.
  3. The hatch door does not close. There is no clicking or blocking of the tank.
  4. Everything is flashing. The situation is the opposite of the first: pressing “Start” causes all the lights on the control panel to blink. Even those that usually remain unlit.

If you see one of the following pictures, reboot the machine. A one-time system failure is possible, but if history repeats itself, you need to dig deeper and carry out repairs yourself. You will have to fix one of the following problems:

  • loose contacts in the socket;
  • lack of power supply;
  • broken cord or broken plug;
  • damage to the power button;
  • faulty FPS;
  • problem with UBL;
  • defective electrical circuit;
  • faulty internal wiring;
  • non-functioning programmer or program switch.

noise filterAn ordinary person can only cope with some of the listed flaws on his own, but there is no need to rush to call the service department. It is better to try to accurately determine the location of the breakdown, because something from the list can be solved quickly and without the involvement of specialists. We’ll tell you further where to start and what to check.

We check and repair

The first step in the instructions on what to do if your Zanussi washing machine stops responding to the “Start” button is to check the power supply. Most startup problems happen due to simple carelessness: they forgot to plug in the cord or didn’t notice that there was no electricity at home.

If the plug is in the socket, there is light in other rooms, and the cycle still does not start, then it is recommended to pay attention to a specific socket. We need to find out more precisely whether there is tension in it. The easiest way is to connect a hair dryer or table lamp to the socket being tested. Lack of response from the devices indicates loose contacts, damaged insulation and necessary repairs. But with the help of an extension cord, you can simply and quickly run the washing machine through another outlet.

Another option is if the power cord to the machine is damaged. This is immediately noticeable: traces of burning, the smell of melted insulation, pinched areas or external cracks clearly indicate that the conductor needs to be replaced. If you have the appropriate knowledge and experience, you can carry out this procedure yourself, otherwise, contact the service department.

When everything is in order with the electricity, you should look for a problem in other places. But we do everything competently and consistently. We disconnect the machine from the network and evaluate the performance of each element that can trigger a shutdown.

Important! Make sure that the washing machine is completely unplugged from the power outlet.

  1. FSP. When not working, the interference filter can allow the general voltage to pass through and prevent the washing machine from starting fully. In this case, when connected to the network, not a single indicator lights up. You can verify the serviceability of the part by “ringing” at the input and output. The non-dialing FSP will have to be completely replaced.
  2. Start button. The problematic key is excluded from the list of possible causes in a similar way to FSP. Each conductor suitable for the button is tested (in the pressed position) and if the result is negative, it is replaced with a new one.
  3. UBL. There are two ways to understand that the washing machine will not start due to a broken hatch locking device. The most accurate way is to measure the presence of a suitable voltage with a tester, and the absence of numbers on the multimeter display will confirm this version. There is another option: try to close the tank door, and the familiar “click” will 60% guarantee a working UBL.
  4. Internal wires. Damaged internal wires cause all indicators on the dashboard to flash simultaneously. In this case, you can try to find leaks yourself, restore insulation and make contacts, but it is better to let specialists completely replace all wiring.

UBL ZanussiIf previous checks have not identified the source of the problem, then nine times out of ten the main control element is to blame.For machines with electromechanical control, you will have to deal with a programmer, and for electronic machines, you will have to deal with a module. It will not be possible to independently test such parts, replace the control unit or repair suitable conductors. Therefore, it is recommended to call a service representative. Moreover, there is always the possibility that the breakdown is purely individual and the cause of the shutdown is in a completely unexpected place. And the timely discovery of this fact will save a lot of money.

Attention! If there is a burning smell near the machine, a slight smoke, sparks or dark spots are visible - under no circumstances should you connect it to the network!

Zanussi machines, like all modern automatic washing machines, are complex units with high-tech electronic “stuffing”. One careless movement and minor repairs will result in very serious and, most importantly, expensive problems. Therefore, it is recommended to soberly assess your strengths and stop at the stage of checking the power supply. And let a specially trained technician do the testing of FSP, UBL, control systems and the instrument panel.

   

3 reader comments

  1. Gravatar Nikolay Nikolai:

    Where is the FSP and how to replace it?

  2. Gravatar Yaroslav Yaroslav:

    How to restart a washing machine, and how to reset your computer!

  3. Gravatar Evgeniy Evgeniy:

    Resistance 100 ohm

Add a comment

We recommend reading

Washing machine error codes